Just How to Replace a Tub
Visit Our WebsiteEach person will have his or her own assumption involving Tools You Need to Install a New Bathtub .
Mounting a tub isn't precisely rocket science, but it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bath tub with a new one is also a moderately tough project. If the old tub is conveniently easily accessible, the job can move speedily; if you need to open up a wall to remove the old bathtub as well as position the brand-new tub, the job is a lot harder. In either case, the project is within a residence handyman's skills, although you will require an assistant to move out the old bathtub as well as set in the brand-new one. Make certain you have qualified yourself for the work as well as are comfortable trying it. Instead of hiring a service provider to take control of a halfway-completed project, it is far better to think about using one prior to you start. Possibilities are you might require a professional plumber to make tube links.
This short article will certainly assist you install a brand-new bathtub in your washroom if you have already gotten a brand-new tub and also don't require to alter the setup of your previous supply of water pipes.
Your tools and material checklist must comprise the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you should do is separate the supply of water. After doing so, activate the faucets to drain any type of water remaining in the system. The process of removing the existing faucets can be quite troublesome due to the limited access that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will come from the pipelines. When the supply pipelines have been eliminated, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to moving on to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a link to the current supply pipelines.
If you require to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the manufacturer provided backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal faucet adapters. The previous type ought to be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Tub
Utilizing the two wooden boards under its feet, place the bathtub in the required placement. The wood boards are handy in equally spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto four small factors.
The following objective is to make sure that the tub is leveled all round. This can be achieved by checking the level and also changing the feet on the tub until the level checks out level.
To install faucets, fit all-time low of the furthest flexible faucet adapter to the proper supply pipe by making a compression join; after that do the exact same for the other tap.
Turn on the supply of water and examine all joints as well as new pipework for leaks and also tighten them if needed. Fill up the bathtub as well as also examine the overflow electrical outlet and the typical outlet for leakages.
Ultimately, repair the bath paneling as defined in the producer's instruction manual. Tiling as well as sealing around the bath tub ought to wait until the bath tub has been used at least when as this will resolve it right into its final placement.
Getting ready for the Installation
To start with, the supporting structure supplied with the bathroom must be fitted (if required) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is essential to see to it that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps device to avoid pressure on the tub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you use all of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final setting.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, causing the water to penetrate the wall in between the bathroom and the tiling, resulting in difficulties with dampness and possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components as well as fittings. They are sold in tubes as well as cartridges, as well as can securing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the bathtub with water before securing, to permit the movement experienced when the tub is in use. The sealant can break fairly early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise quickly offered on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very focused on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you liked our blog posting. For those who enjoyed reading our post please do not forget to share it. I am grateful for your time. Please come visit our site back soon.
Visit Page